null
×
close

Performer AMC Engine Intake Manifold

(No reviews yet) Write a Review
UPC:
00085347021314
Availability:
This part ships direct from the manufacturer, lead times, stock and shipping may vary.
Weight:
20.20 LBS
$454.55

#SAVETHEFULLSIZEJEEP

A Portion Of The Proceeds From Your Purchase Supports The Development & Reproduction Of High Quality 1963-1991 Restoration Parts.

Performer AMC Engine Intake Manifold

Performer AMC Engine Intake Manifold

$454.55

Edelbrock Performer AMC intake manifold is designed for 1970-91 street 304-360-401 c.i.d. V8 engines. Will not accept stock Motorcraft spread-bore carburetor. Edelbrock's Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent throttle response from off-idle through 5500rpm. The Performer intake manifolds are ideal for passenger cars, trucks, 4x4s, tow vehicles and RVs.

Installation Instructions



This Part Fits:

 

Year Make Model Submodel
1974 Jeep Cherokee  
1975-1983 Jeep Cherokee  
1972-1981 Jeep CJ5  
1972-1975 Jeep CJ6  
1976-1981 Jeep CJ7  
1984-1991 Jeep Grand Wagoneer  
1972-1973 Jeep J-2500  
1972 Jeep J-2600  
1973 Jeep J-2600  
1974 Jeep J10  
1975-1988 Jeep J10  
1974 Jeep J20  
1975-1988 Jeep J20  
1972-1983 Jeep Wagoneer  



Applications AMC:Small-Block:304 (5.0L)/360 (5.9L)/401 (6.6L)
Description Edelbrock Performer AMC Intake Manifold for 1970 and Later 304-401 c.i.d. AMC V8 Engines is Designed for use with 4150-Style Square-Bore Carburetors. (Will not accept stock Motorcraft Carburetor). Non-EGR
Description_TRA Recommended intake gasket: Edelbrock #7213 Fel-Pro MS96011; Must use factory style metal valley tray; Manifold height: A-4.20", B-5.50"; Carb pad height: 4.85"; Requires #8008 or #8024 Stud, nut and washer kit.; Car recommendations: OEM 4-Bbl . Non-EGR square-bore Edelbrock AVS2 or Performer Series 500-650cfm.; Port exit dimensions: 1.03" x 2.07"; #2131 must use factory style metal valley tray.; Manifolds have two center bolt holes offset.; Edelbrock bracket #8034 required for 1979 and later vehicles.; Use RTV sealant to properly seal end seals, such as Edelbrock High Temp Silicone sealant #1076, DO NOT USE END SEALS GASKETS.; Hardened washers Must be used with intake bolts to ensure proper torque and prevent galling of the aluminum.; Manifold will not accept factory Motorcraft spread-bore carburetors.
RGL WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov.
Series Performer
Vehicle Model AMC/Jeep

To submit a return or exchange request, please go to our Contact Us page to submit order information. Photos of any damaged products may be requested and required to process any full or partial refund. If approved, we will provide you with an RMA number along with a return label for shipping.

Parts returned that are not defective, are subject to a 25% restocking charge. JeepRecyclers.com/McDaniel Motor Co. is NOT responsible for any parts that have been altered, modified, disassembled, or damaged by misuse or an accident subsequent to the parts purchase.

Reconditioned parts come with a minimum warranty of 90 days, unless otherwise stated (Refer to product listing for warranty duration). The warranty is void if the parts are not returned in the same condition in which they are sold. Warranties for aftermarket parts are covered by the manufacturer.

What Are My Shipping Fees?

For orders delivered within the continental US where reason for return isn't a result of a JeepRecyclers.com/McDaniel Motor Co. error, the cost of the initial shipping charge and a return fee will be deducted from your refund. A prepaid shipping label(s) will be provided. The flat fee for each item being returned can be found in the chart below:

Retail cost of the item Per Item Return Fee
Less than $25.00 $3.75
From $25.00-$49.99 $5.75
From $50.00-$99.99 $7.75
More than $100.00 $9.75

More

to top