My Account
If you are already registered, please log in.
Create your account and enjoy a new shopping experience.
Create A New Account
#SAVETHEFULLSIZEJEEP
A Portion Of The Proceeds From Your Purchase Supports The Development & Reproduction Of High Quality 1963-1991 Restoration Parts.
Edelbrock Performer-Plus Camshaft #2132 is designed for 290-401 AMC V8 engines and produce optimum torque from the low-end to the mid-range. Performer-Plus camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm. The Performer-Plus #2132 is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. In the manifold section you'll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams. All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions. This cam produced 275 Ft Lbs of Torque when paired with Performer AMC intake manifold #2131 and stock cylinder heads. Camshaft specifications: - Intake duration: 204 Degrees - Exhaust duration: 214 Degrees - Intake lift: .448" - Exhaust lift: .472" - Lobe separation: 110 Degree - Intake Center Line: 105 Degree - Vacuum: 15"
Installation Instructions
This Part Fits:
| Year | Make | Model | Submodel |
|---|---|---|---|
| 1974-1983 | Jeep | Cherokee | |
| 1984-1991 | Jeep | Grand Wagoneer | |
| 1972 | Jeep | J-2500 | |
| 1973 | Jeep | J-2500 | |
| 1972 | Jeep | J-2600 | |
| 1973 | Jeep | J-2600 | |
| 1974-1988 | Jeep | J10 | |
| 1974 | Jeep | J20 | |
| 1975-1988 | Jeep | J20 | |
| 1972-1983 | Jeep | Wagoneer |
| Applications | AMC:Small-Block:290 (4.8L)/304 (5.0L)/360 (5.9L)/390 (6.4L)/401 (6.6L) |
| Description | Edelbrock Performer-Plus #2132 is designed for 290-401 AMC V8 engines and produce optimum torque from the low-end to the mid-range. |
| Description_TRA | Recommended Valve Springs for OEM heads: Edelbrock part #5832 non-rotator/# 5932 Rotator; In order for this Performer-Plus cam and lifter kit to be covered under ANY WARRANTY you must use either the correct Edelbrock Sure Seat valve springs or the stock original equipment valve springs.; Oil/additive must contain Zinc designed for use with flat tappet camshafts.; Coat cam lobes and bottoms of each lifter with MoS2 lube (supplied) to prevent cam lobe and lifter wear from occurring during initial start-up.; Do not allow the engine to run under 2000 rpm for the first 1/2 hour. Slow idle speeds may result in severe cam and lifter wear. Start the engine and bring to break-in rpm. |
| RGL | WARNING: This product can expose you to Chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov. |
To submit a return or exchange request, please go to our Contact Us page to submit order information. Photos of any damaged products may be requested and required to process any full or partial refund. If approved, we will provide you with an RMA number along with a return label for shipping.
Parts returned that are not defective, are subject to a 25% restocking charge. JeepRecyclers.com/McDaniel Motor Co. is NOT responsible for any parts that have been altered, modified, disassembled, or damaged by misuse or an accident subsequent to the parts purchase.
Reconditioned parts come with a minimum warranty of 90 days, unless otherwise stated (Refer to product listing for warranty duration). The warranty is void if the parts are not returned in the same condition in which they are sold. Warranties for aftermarket parts are covered by the manufacturer.
What Are My Shipping Fees?
For orders delivered within the continental US where reason for return isn't a result of a JeepRecyclers.com/McDaniel Motor Co. error, the cost of the initial shipping charge and a return fee will be deducted from your refund. A prepaid shipping label(s) will be provided. The flat fee for each item being returned can be found in the chart below:
| Retail cost of the item | Per Item Return Fee |
|---|---|
| Less than $25.00 | $3.75 |
| From $25.00-$49.99 | $5.75 |
| From $50.00-$99.99 | $7.75 |
| More than $100.00 | $9.75 |
Converting your NON-AMC era FSJ Engine to an AMC V8 304, 360,401? these engine mounts will fit nearly all AMC V8 engines, Each mount set contains left and right frame mount sets, two sets of...
Clevite
Clevite AMC/Jeep 290 304 343 360 390 401 V8 1966-91 Main Bearing Set. These Tri-Metal 77 engine bearings combine the strength of a copper-lead alloy layer with steel backing and an electroplated...
Edelbrock
Edelbrock part #7132 Performer RPM Camshaft is designed for AMC 343-401 V-8 applications. This Edelbrock cam kit produced 433 HP & 489 ft-lbs. of torque when used with #7531 intake and #60119...
Edelbrock
Edelbrock part #3731 Performer AMC EGR intake manifold is designed for 1970-91 street 304-360-401 c.i.d. V8 engines. This intake manifold will not accept stock Motorcraft spread-bore carburetor...
Omix
Omix proudly offers all the parts you need to keep your Willys/Jeep running like new with quality standards that always meet or exceed those of the factory part. This replacement lower engine gasket...
